General

Physical properties

Technical data

Directions for use

Soaked method
This method is an effective way of cleaning deposits from machine parts. The items to be cleaned are dipped into the cleaning solution. A wire basket can be used for small components. For removal of light deposits or oil, a dilution of up to 1:2 in fresh water can be used. Light deposits will be removed in 1 hour, whereas heavily oxidised deposits may need overnight soaking. After the components have been removed from the soaking bath, remaining cleaning solution is easily flushed off with water.

Due to a very low evaporation rate, no precautions are necessary to prevent loss of liquid, but adequate ventilation is recommended.

Cleaning the Oil Side of Heat Exchangers Where in-site cleaning is required, Unitor™ Carbonclean LT™ can be used neat and circulated through the unit in question. Time required for this process will again depend on extent of fouling and may take up to 24 hours.

The Unitor™ Chemical Cleaning Unit - Product no. 737189 - is recommended to be used.

1. Disconnect the heat exchanger's oil inlet and outlet, drain off any remaining oil.
2. Connect the discharge side of the Chemical Cleaning Unit (CCU) to the lower heat exchanger connection and fit the return to the CCU.
3. Add Unitor™ Carbonclean LT™ to the drum, Unitor™ Carbolcean LT™ can be diluted to 25% with fresh water, and heat, maintaining the temperature (max 60°C), throughout the cleaning operation. If heat is not available the cleaning time will need to be extended and a higher product concentration is beneficial.
4. Circulate for 12 hours. When the cleaning is complete, disconnect the lower heat exchange connection and drain out the cleaning solution.
5. Connect a fresh water supply to the upper heat exchanger connection. Rinse until water runs clear.
6. Disconnect the water supply, drain and dry the heat exchanger.

The Unitor™ Chemical Cleaning Unit can also be used for cleaning by soaking or circulation. Results can be achieved with maximum efficiency and with the minimum use of Unitor™ Carbonclean LT™.

产品特性

• 改良后的清洁性能

• 可用于清洁发动机部件，包括但不限于：

• 活塞

• 活塞环

• 阀

• 阀壳

• 不含壬基酚乙氧基化物或其他雌激素化合物

• 通过浸泡或循环方法使用简单且经济

• 低毒性和蒸发率

• 无酚类或氯化物

• 清洁燃油侧面和润滑油加热器，油冷却器等。

• 去除燃油和润滑油过滤器中的碳基沉积物

优势

• 对所有轻金属（包括铝）均无腐蚀性，安全

• 快速溶解含碳，树脂或清漆的沉积物

• 无需进行硬刮

• 有效去除燃烧器尖端，燃油喷射器和碳，树脂或清漆污染的所有组件中的碳类沉积物

订购信息

Product number                           Product name

575696                                       CARBONCLEAN LT 25 LTR

使用说明

浸泡的方法

该方法是清除机器零件沉积物的有效方法。将要清洁的物品浸入清洁溶液中。金属丝篮可用于小型部件。为了去除轻质沉积物或油，可以使用淡水中最多1：2的稀释液。轻度沉积物将在1小时内被除去，而高度氧化的沉积物可能需要在一夜之间浸泡。从浸泡浴中取出组分后，很容易用水冲洗掉剩余的清洁溶液。

由于蒸发率非常低，因此无需采取任何预防措施来防止液体流失，但建议进行充分的通风。.

清洁换热器的油侧如果需要进行原位清洁，Unitor™ Carbonclean LT™可以整齐地使用并通过相关装置循环。此过程所需的时间将再次取决于结垢程度，可能需要长达24小时。

建议使用Unitor™ Chemical Cleaning Unit - Product no. 664613807

1. 断开热交换器的进油口和出油口，排出剩余的油。

2. 将化学清洗单元（CCU）的排放侧连接到下部热交换器连接，并将返回装置安装到CCU。

3. 将Unitor™Carbonclean LT™添加到转鼓中，Unitor ™Carbolcean LT™可用淡水稀释至25％，并在整个清洁操作过程中加热，保持温度（最高60°C）。如果没有热量，则需要延长清洁时间，并且更高的产品浓度是有益的。

4. 循环12小时。清洁完成后，断开下部热交换连接并排出清洁溶液。

5. 将淡水供应连接到上部热交换器连接。冲洗直至水流清澈。

6. 断开供水，排干并干燥热交换器。

The Unitor™Chemical cleaning unit也可用于浸泡或循环清洗。