Directions for use

Soak Method
This method is an effective way of cleaning deposits from components and machine parts. In order to reduce the evaporation of Unitor™ Carbon Remover™ both on the pure product as well as on its emulsions, a skin is formed when exposed to air.

The items for cleaning are submerged into the active solvent. A wire basket can be used for small components. Immersion time will depend upon the nature of the deposits to be removed. Light deposits will be removed in 1 hour, whereas heavily oxidised deposits might need longer time.

The components should be rinsed thoroughly before handling.

Cleaning the Oil Side of Heat Exchangers
The Unitor™ Chemical Cleaning Unit - Product no. 664 737189 - is recommended to be used.

1. Isolate the oil supply, disconnect the heat exchanger oil inlet and outlet, drain off any remaining oil.
2. Connect the discharge side of Unitor™ Chemical Cleaning Unit (CCU) to the lower heat exchanger connection and fit the return to the CCU.
3. Add Unitor™ Carbon Remover™ to the drum, product can be diluted with diesel oil down to 25 % and heat, maintaining the temperature (max 50°C) throughout the cleaning operation. If heating is not available, the cleaning time will need to be extended and a higher product concentration is beneficial.
4. Circulate for 12 hours. When the cleaning is complete, disconnect the lower heat exchanger connection and drain.
5. Connect a high pressure fresh water supply to the upper heat exchanger connection. Rinse until water runs clear.
6. Disconnect, drain and dry.

产品特性

• 快速溶解含碳，树脂或清漆的沉积物

• 无需进行硬刮除

• 非易燃

• 去除燃烧器尖端燃料中的碳类沉积物注射器和所有被碳，树脂或清漆污染的组件

• 清洁燃油加热器，油冷却器等的油侧。

• 去除燃油和润滑油过滤器中的碳基沉积物

• 可用于清洁：- 活塞- 活塞环- 阀门保持架

优势

• 使用简单，经济

订购信息

Product Number          Product name

571604                 CARBON REMOVER 25 LTR

使用说明

浸泡法

该方法是清除部件和机器部件沉积物的有效方法。为了减少Unitor™Carbon Remover™在纯产品及其乳液上的蒸发，暴露在空气中会形成皮肤。

清洁物品浸没在活性溶剂中。金属丝篮可用于小型部件。浸入时间取决于要除去的沉积物的性质。轻度沉积物将在1小时内被移除，而高度氧化的沉积物可能需要更长的时间。

处理前应彻底冲洗组件。

清洁换热器的油侧

建议使用Unitor™Chemical Cleaning Unit - 产品编号。664737189 。

1. 隔离供油，断开热交换器的油口和出口排出剩余的油。

2. 将Unitor™化学清洗单元（CCU）的排放侧连接到下部热交换器连接，并将返回装置安装到CCU。

3. 将Unitor™Carbon Remover™添加到滚筒中，产品可用柴油稀释至25％和热量，保持温度（最高50°C）整个清洁操作。如果没有加热，则需要延长清洁时间，提高产品浓度是有益的。

4. 循环12小时。清洁完成后，断开下部热交换器连接和排放。

5. 将高压淡水供应连接到上部热交换器连接。冲洗直至水流清澈。

6. 断开，排空并干燥。